Always one more accessory to glue on, when you figure it's about time to do the last round of filling and fairing.
This is the off-set for the centerboard up haul block to keep the centerboard tackle from banging against the sides. (As much.)
20250406_131531 1024X768.jpg
All the screws removed after gluing, filled with bamboo sticks and epoxy glue.
20250406_131534 1024X768.jpg
All the over-drilled holes filled.
20250406_131537 1024X768.jpg
On both sides.
20250406_131542 1024X768.jpg
Also filled in the hatch mounting holes.
20250406_131604 1024X768.jpg
And sanded smooth.
20250407_175558 1024X768.jpg
More coats of epoxy for the compass box and the motor mount and the fishing rod holders.
20250406_131659 1024X768.jpg
Two layers of glass on one side of the motor mount.
20250407_135425 1024X768.jpg
After trimming, the holes were filled with thickened epoxy.
20250409_100622 1024X768.jpg
And two layers of glass applied to the other side.
20250409_165652 1024X768.jpg
Transom sanded flush and ready for the next round of holes!
20250407_175428 1024X768.jpg
This is why I didn't over-drill all four gudgeon holes at the same time.
20250408_154539 1024X768.jpg
It allowed me to use the gudgeons as a template for drilling the center holes, so as not to have to re-measure everything all over again.
20250408_154709 1024X768.jpg
Like so.
20250408_155548 1024X768.jpg
And allowed me to over-drill the outside holes.
20250408_161641 1024X768.jpg
And fill with epoxy.
20250408_165945 1024X768.jpg
And drill when sanded, using the gudgeons as templates once again.
Things are easy, when you plan ahead.
20250409_102931 1024X768.jpg
Here's all the holes in the transom, over-drilled, filled and re-drilled.
Notice that no fastener will touch wood, but only epoxy.
20250409_181346 1024X768.jpg
What is all that filler in the trolling motor socket, in the upper left corner? ???
>:( I DONWANNA TALK ABOUT IT!! >:(
I had previously used a Forstner bit to over-drill some holes in the side compartment cleats and fill them with epoxy.
20250409_114134 1024X768.jpg
Now it was time to drill the final holes because after painting, I won't know exactly ??? where the epoxy-filled holes are located.
20250409_114145 1024X768.jpg
This is what we're drilling the holes for. Have one of these on Urchin and use it for storing lines, fenders, etc.
Very handy and far easier to do now, 8) than after the seat tops are installed.
20250409_114159 1024X768.jpg
Next, I taped off all the surfaces that will need epoxy later on, when the seats and the sole goes down.
20250410_193503 1024X768.jpg
The blue tape on the inside of the transom is to keep paint from dripping down the holes, when I paint the outside of the transom with EZ-Poxy primer.
Last of the taping off.
20250410_193513 1024X768.jpg
Tape on the bow is to keep paint from dripping out the holes, from the inside.
And after the first coat (of 3 coats) of paint for the interior compartments..
20250411_180134 1024X768.jpg
This is where the LiFePO4 batteries will go.
20250411_180136 1024X768.jpg
View looking aft at the lazarette and side compartments
20250411_180140 1024X768.jpg
Looking forward.
20250411_180150 1024X768.jpg
Anybody says this is a small dinghy, should have to paint it! >:(
Today's Southern Boat Builder's Tip:
Try not to paint outside, during Pollen Season!! :'(
20250411_180120 1024X768.jpg
Ah, well. It will sand right off in the morning. :P
Nice to finally see some visible progress. ;D
Charles Brennan
Thumbs up!
All it takes is elbow grease! And money, and time, and lumber, and paint, and line, and....
Well, you get the idea. It's beginning to look floatable!!
You left out sanding, sanding, and more Sanding!
I think the biggest thing here is Charles planning ahead, so all those steps are done once.
There are many of his steps that are not essential for a passable outcome, but not an ideal outcome.
There is a place between "perfect" and "good enough", and Charles seems to find it.
He also makes me tired just reading about all those steps. My professional career had similar requirements, with days spent devising exactly how the required outcome would be assured, no possibility of failure, before a 500,000,000 watt generator was removed from service for the modification.
My consistent success made me a first choice for all of our power plant managers. They pestered me monthly for the first 3 years of my retirement, then I went back for 5 years of contract work.
The next owner should have an outstanding boat, the Brennan years will not compromise the integrity of his build.
Keep up the good work, Charles, if I survive long enough, I would like a sail on her.
KRUSEN, without a boat anymore.
Krusen, Whenever I see your tag on a SCAMP progress post, my first thought is:
"What did I get wrong, or could have done better?!?" :o
My Dad used to prize prior planning; explaining that if you built a house and didn't plan ahead far enough, you'd suddenly find yourself needing an eight-foot nail. :P
He's long gone, but his prejudices live on and inform much of what I do, on this build.
" . . . . . if I survive long enough, I would like a sail on her."
Actually, that sentiment goes, for BOTH of us!! :o
Sailing the Chesapeake has always been on my Bucket List, along with sailing in Mystic, Connecticut and sailing to Fort Jefferson, in the Keys. Can't believe I've owned Urchin nearly 50 years and still haven't managed it. :P
Ah, well.
Thanks for all the encouragement.
I hope very much to have you aboard some day,
Charles Brennan
Charles, if you come to sail the Chesapeake, with sufficient advance notice, I can find you meals and a place to stay, just cost you a sail.
KRUSEN