Painting the first coat on the underside of the bench seats.
I really noticed the difference in how easy it was to see things, when I painted the interior compartments, so I figured available light reflecting from the underside of the bench seats, would probably also be a good thing.
20250421_140409 1024X768.jpg
I was not happy :( with the way the 6 mm fore deck "oil-canned", back when I was first playing with all the pieces to see how the boat fit together.
I do a lot of hanging out on fore decks at launch, docking, or beaching, etc. and I wanted some more support, than what the stock support from the center beams provides.
The logical solution would be additional support beams, but they would have been a nightmare to reach through and around to paint; it was tight enough quarters as it was.
20250415_160539 1024X768.jpg
So I waited until the interior was finished with painting, to add the additional support beams.
They were glued in on one day and got their first coat of paint on the sides (and bottom), the next day.
(And Yes. >:( It WAS a pain to reach under the beams, to paint).
20250421_140420 1024X768.jpg
Just another one of those things that everyone tells me I don't really need; causing me to stubbornly go my own way. ::)
I really DO listen to all the advice I seek, and I think about it quite a lot, before I decide to deviate from the norm.
The biggest impetus, was the fear of getting the whole boat built and then having the fore deck "oil-can" on me and KNOWING :o I could have fixed it, way back when.
And didn't. :P
On the on-going motor mount project, got the fourth coat of epoxy on; this time it was graphite infused.
20250421_152002 1024X768.jpg
Got it pretty smooth! 8) When you can see your reflection . . . . . .
20250421_152011 1024X768.jpg
Let it sit overnight.
Then flipped it over the next day, and got the other side coated.
20250422_174020 1024X768.jpg
So what do you do with a shiny block of wood? ???
Sand it until it's dull, of course.
20250425_145140 1024X768.jpg
So you can apply a primer coat.
20250425_145806 1024X768.jpg
With all the hull primer painted on and sanded smooth, and while waiting for bench seats and motor mounts to cure/dry, there was no other reason not to move forward and paint the hull.
Especially with the low humidity and mild temperatures we're getting, lately. :)
20250422_102225 1024X768.jpg
Most of my pics are taken after the fact, since in the throes of construction and fighting curing times/drying times, and not wanting to grundge up the camera, there's not always time to stop in the middle and take an in-progress pic. :P
But I decided to give it a shot for once, right in the middle of painting and it only cost me an extra pair of latex gloves to do so.
First coat on the hull! :D
Made a big difference, both in appearance and in my personal attitude.
Been having a Massive Mental Pity Party, :'( since the SCAMP is not going to make it in time for the Cedar Key Small Boat Meet, in May.
The bright colors, brightened my spirits, a lot. :)
20250422_111222 1024X768.jpg
And it took nearly .087 femto-seconds (10 -15 seconds) for a gnat to find the wet hull and entomb himself. >:(
(Or, 870 atto-seconds; the amount of time it takes light to travel the length of a coupla Hydrogen atoms, for those of you keeping track.)
20250422_111259 1024X768.jpg
Second coat of paint on the bench seats.
20250422_113533 1024X768.jpg
I vaguely wondered if I really needed a third coat, but then realized it was just Impatience trying to Rationalize a Shortcut. :-\
I haven't: "mickey-moused" it this far; keep to the plans and to SCAMP standards and practices, Brennan! >:(
At times like that, it's instructive to review what happened, when a guy got impatient while building a SCAMP, and then Doug SC acquired it and had to fix it.
DSCN8949 1024X768.JPG
It's pics like that, that keeps me honest. :o
Thanks, Doug.
And so, I did. 8)
Coat #3 and the tape removed for the bulkhead gluing surfaces in the hull.
20250424_105610 1024X768.jpg
With the bench seat tops now out of the way, I could move on to the cuddy sole/ballast tank cover (foreground) and to the lazarette top and doubler (background).
Gathered all my clamps again.
This is the first time I've had to glue a puzzle joint together, and I was a little apprehensive that I would screw something up.
Hedged my bets a little, by keeping the glue in the fridge while I coated the wood with epoxy and then painted all that puzzle joint surface area with an acid brush, to apply the glue.
20250424_131420 1024X768.jpg
And once again, every clamp I owned wasn't really as much as I wanted, but I did get enough squeeze-out to convince me that I must have had enough clamps, after all.
The 2 X 4's on either side of the puzzle joint were covered in wax paper and clamped really hard, since squeeze-out wasn't the goal, so much as achieving a completely flat scarf.
20250424_142555 1024X768.jpg
Lazarette top and doubler, first coat and glued.
20250424_142600 1024X768.jpg
Sanded all the glue slop and got the second coat of epoxy down.
20250425_110209 1024X768.jpg
An on-going mental exercise was how to put a flare in both ends of the centerboard pipe without trashing the glue joint.
I had used a flat-head ¼-20 machine bolt to flare one end with great success, but had to leave the other end straight to insert and glue it in the centerboard trunk.
But I really wanted it flared at both ends, to minimize possible line chafe.
20250409_180443 1024X768.jpg
After some thought, ??? I drilled a small pilot hole in a ¼-20 acorn nut then drilled it larger with a 7/32" bit and tapped it with a ¼-20 tap, as shown below.
20250409_175307 1024X768.jpg
Threaded the nut onto the bolt, backwards.
20250409_175904 1024X768.jpg
Then I inserted the ¼-20 flat-head bolt in the trunk, and threaded the backwards nut on and cranked down on it.
20250409_180428 1024X768.jpg
It flared the straight end nicely and didn't deform anything, or stress the glue joint inside the centerboard trunk.
20250409_180853 1024X768.jpg
Another back-burner project, was getting corners into my compass box so that I can screw the lid to the box, at some point.
All epoxied and finally glued in.
20250422_174028 1024X768.jpg
Started the holes for the compass mount; I'm going to use nylon screws and nuts to mount the compass. No metal will be adjacent to the compass.
20250425_131013 1024X768.jpg
Over-drilled and ready to fill the holes with epoxy.
We don't often enough, acknowledge the valuable contributions from other TSBB viewers.
Back in January, Krusen mentioned tapping ¼-20 threads into oak, to mount some hand rails.
That sparked an idea of using a ¼-20 tap, to tap threads into an epoxy-filled hole.
This way, I can unscrew the face plate multiple times without tearing up wood, like a wood screw or sheet metal screw would.
Then I came up with the idea of using a nylon ¼-20 pan head screw to hold the face plate; keeping any metal (ferrous or non-ferrous) away from the compass.
THANKS!! ;D NORM!! ;D
20250425_134927 1024X768.jpg
The more niggling little details I can get off my plate, the better I feel.
The most interesting thing about a SCAMP build, is that all the individual steps are fairly simple.
But there's a LOT of those steps!! :o
Charles Brennan
Thanks for the credit for threading the wood, or in this case, the epoxy. I have used a lot of nylon screws and bolts in magnetically sensitive locations. Do not over torque them as all the stretch will be in the short distance between the epoxy and faceplate. Those screws stretch easily, but fail slowly, a year or two. I replaced factory installed ones for that failure, after 2 failed, I replaced all the rest.
Fine workmanship throughout, Charles, as usual.
A lot of steps indeed! Painting the hull is a huge step. Great satisfaction in that.
Mentioning Cedar Key, I really want to attend. Of course, there's the FL120 too. I really hope when you finish we can attend one at the same time. Maybe next year.
As it turns out, there is a small gathering May 2-4 just north of Atlanta on Lake Lanier that I'm planning on attending for the Fri/Sat time. Just 2 hours from me so doable.
And that boat is going to be a tank when you're done! Keep up the good work.
Oh, that reminder of rotten wood and chasing leaks brings back fond memories...NOT! However, it's because of the problems that I acquired the boat for $1,500 the rest of the cost has been mostly repair time and aggravation but not much extra money. Upgrades on the other hand have added further cost, but those were my choices. There isn't any way for me to easily bring my Scamp up to the standards of yours, but it should suffice long enough for the time left to me and my sailing days on the water. I am very impressed with your due diligence.
I just returned from 6 days visiting with my Dad in Florida. Rented a house on a small lake near Apopka and would put my canoe in to paddle each morning. We missed his 101 birthday last fall due to Carol's health. So, it was good to spend time with him. I hope to get down your way again and this time with my Scamp.
DSCN7218az.JPG