I was still coating the dead lights and the hand rail backers, when I had to re-visit the cockpit hinged locker. (Lower left of pic.)
It occurred to SOMEBODY, :P that the centerboard up-haul tackle once installed, would preclude actually OPENING >:( the locker!
DOHHHHH!!!! :-[
So a notch was cut in the starboard side, sanded, shaped and epoxied, and all is well again. :)
I'm mostly finding these issues, by visualizing the finished boat and then mentally getting beaten about the head and shoulders, every time Reality rears it's ugly head. :o
Lord knows, the PLANS are no help! :'(
Especially, because I keep adding in Cool Things, that aren't IN the plans. 8)
Hence, the sometime re-adjustments to the build. :-X
20250522_164945 1024X768.jpg
Ah, well.
That tape-the-back trick is paying off well; I'll be doing that to the hand rail backing doublers, when I flip them over.
20250524_134338 1024X768.jpg
So how DO you move an unwieldy, floppy, boat deck all by your lonesome? ???
It's not a matter of weight, so much as bulkiness so first off, make it less floppy.
20250523_094825 1024X768.jpg
Then lift it up on one side and simply plop it down on the hull! :D
20250523_095044 1024X768.jpg
EASY!! ;D
Figured I'd need roughly 2½ times the total number of clamps I currently own, to clamp this deck down properly for gluing down with epoxy.
Couldn't see buying several hundred dollars worth of clamps, for what will essentially be a single-use application and then just gather dust in the garage, for the rest of my life. ???
So I placed enough clamps to hold the deck in position on the hull.
20250523_101053 1024X768.jpg
Needed a few more clamps up front, to position all those compound curves.
20250523_101059 1024X768.jpg
A good thing about saving all your plywood scraps, is that you can make a ton of clamping blocks covered in packing tape.
Drill a bunch of holes and use a box of screws and you're good to go! :D
This is NOT the Glue-up; this is pre-position and pre-fit, to get ready to glue the deck down.
20250523_113441 1024X768.jpg
Now, instead of needing several hundreds of dollars worth of clamps, all I need is a bag of bamboo skewers!! ;D
After getting the deck locked down, I discovered I hadn't read the build manual, quite closely enough. ???
Missed the part about beveling the bulkhead cleats, since the cabin sides curve around bulkheads #'s 2, 3, & 4.
Woulda SWORN I had the whole build manual just about memorized by now, but I sure missed that one word: bevel. :-[
20250523_091942 1024X768.jpg
Ah, well. Easy fix with a Sawzall.
After sanding the bevels smooth, (Sawzalls are effective, but they are NOT subtle) I elected to screw the cabin sides temporarily, to the bulkhead cleats.
This will give me a couple of advantages over just using clamps. It will provide a reference point (the screw-holes) and ensure both up and down and fore and aft alignment of the cabin sides, after the deck is glued down.
Having the deck temporarily in place allowed me to cut a notch in the cabin sides where it sits on the deck and also allowed me to cut, fit and trim, fore and aft cabin side doublers.
Forward doubler being scribed.
20250523_161249 1024X768.jpg
After cutting. (And yes, MORE beveling!) >:(
20250523_162710 1024X768.jpg
After the doubler and cabin side is glued together, I can cut in a drainage notch; something that is a Major Pain to do, after the sides are already glued down.
I'm trying to spare myself, as much pain as possible! :o
Especially, since it chews up far fewer man/hours of labor. :P
And fitting the aft cabin side doubler.
20250523_163225 1024X768.jpg
Starboard aft side, pre-trim.
20250523_163304 1024X768.jpg
And after final trim.
20250523_163631 1024X768.jpg
I see numerous build blogs where those doubler pieces are cut, fitted, and installed, AFTER the cabin sides are glued and screwed down.
Man! That looks like a LOT of work! :o
By having the bulkhead screws as a reference point, I can coat and glue the doublers at each end, on a work surface (less drips to sand out) and install the whole completed panel whenever it is coated both sides, and can be affixed at my leisure.
I can start coating these, right after I get the deck glued down.
Put a strip of tape on the gunnels, so that (besides protecting them from epoxy and glue drips!) I could mark everything before I put the deck down.
It will go much more quickly, if you're not constantly reaching underneath, to find out where a backer block is.
Vertical lines denote beginning and end of backing blocks, double vertical lines denote a bulkhead.
Abbreviations denote Rod Holder, Cleat, and Re-Boarding Strap.
The dots denote where the rub rail will be screwed to the gunnel into an over-drilled, epoxy filled, re-drilled hole.
Tried as much as possible, to make sure I could always reach the other side of the gunnel, to get the nut onto the 10-24 screw.
20250524_102233 1024X768.jpg
EXCEPT!! :P In two spots.
DOHHHH!!! :-[
20250524_103529 1024X768.jpg
Going through all the effort of using machine screws and nuts, because I fully expect the rub rails to get beat up over time and require replacement, on occasion.
(I've SEEN, :o how I dock!!) :-[
Just don't understand anyone that would permanently glue a sacrificial piece of wood, to a boat. :-\
The obstructed spot was an easy enough fix, with a Forstner bit. (Two blocked mounting holes out of 24, can't complain.)
Notice the edges are sanded, in preparation for a final coat of epoxy before gluing; I'll coat the inside of the holes I just made, at the same time.
20250524_104736 1024X768.jpg
Added paper masking before the final epoxy coat gets applied.
(I know just what kind of a slob I am, with epoxy and glue!) :P
Here's the final coat of epoxy, prior to gluing the deck onto the frame members.
20250524_143348 1024X768.jpg
(Sigh.) :(
I really TRIED to avoid any drips and even thought I had done so, until the next morning, when I was rudely disabused of my unfounded optimism. :'(
Probably should have masked off the insides, as well.
I can do some paint touch-up after everything gets really cured. I've learned my lesson about trying to paint over epoxy, that is still out-gassing VOCs. ::)
20250525_085334 1024X768.jpg
Remember the bulkhead clamp trick, for keeping the floor up and out of the way, until needed? ???
Works for deck assemblies, too! :D
This allowed me to keep the fore deck off the glue, while I was at the back, aligning the screws with the screw-holes in the corners.
20250525_085246 1024X768.jpg
Aligned the screws with the screw holes and got surprisingly good alignment, throughout. 8)
Then I started screwing down all the blocks.
20250525_120630 1024X768.jpg
Near heart failure, :o when I peeked underneath each side of the bow and saw "waves" of plywood, where the wood held down by the screws made "ripples" on the deck.
A clear indication that the compound curves needed far more clamping surface area than I had figured on, the day before.
Quickly pressed my clamps into service and though that might look like an over-reaction; trust me, it's not.
No more ripples.
(Side decks were fine, BTW.)
20250525_120616 1024X768.jpg
I'll move on to getting multiple coats of epoxy on the cabin sides, while all that cures.
While I'm not exactly multi-tasking, I AM sequencing the build steps just as efficiently as I possibly can.
After all, this project has cost me (so far!) a year and a half of my LIFE! :'(
And caused me to miss out on: :(
1) A Columbus Day Cruising Regatta.
2) A Cedar Key Small Boat Meet. (Well, in my own boat, anyway.)
3) A Florida 120.
4) Probably a BEER Cruise.
Still and all, it's going to take as long as it takes, and that's all there is to it.
With the deck out of the way, I rearranged my work area and laid out all the cabin sides components.
20250525_141733 1024X768.jpg
Including the forward cabin side doublers and the hand rail backing doublers.
20250525_141737 1024X768.jpg
First coat on the cabin sides.
20250525_143624 1024X768.jpg
And a second coat on the hand rail backing doublers.
20250525_143629 1024X768.jpg
Omigosh!! :o
Starting to look recognizably, like a BOAT!
20250525_144432 1024X768.jpg
A far cry from the partial build I dragged out of a Wisconsin barn, 18 months ago.
Scamp_Barn 1024X768.jpg
But also, still a far cry from something that looks like this:
Scamp_1 1024X768.jpg
In my defense, I had my colors picked out long before I ever saw this pic of a SCAMP, built by designer John Welsford and displayed at the Australian Wooden Boat Festival.
Apparently, we just have similar Good Taste. 8)
And my colors are Sea Foam, not Aqua and Hatteras Cream, not White. The cabin roof will be the same Grand Banks Beige, though.
When my wife saw this pic, she loved the port hole colors and dissuaded me from painting the porthole frames an ersatz bronze as I originally intended; so they will now be Sea Foam, also.
AustralianWoodenBoatShowScamp.jpg
Yeah. A long ways off, still.
But, I'm getting there!! ;D
Charles Brennan
I do have to wonder what Heloise Hinkley thinks about all this. You are now a number of steps closer to the finish line, and when you cross that line you will know it is a job well done.
She is looking like a boat!!!
You shouldn't call Heloise a boat! :o
Quote from: Charles Brennan on May 25, 2025, 05:28 PMI was still coating the dead lights and the hand rail backers, when I had to re-visit the cockpit hinged locker. (Lower left of pic.)
It occurred to SOMEBODY, :P that the centerboard up-haul tackle once installed, would preclude actually OPENING >:( the locker!
DOHHHHH!!!! :-[
So a notch was cut in the starboard side, sanded, shaped and epoxied, and all is well again. :)
I'm mostly finding these issues, by visualizing the finished boat and then mentally getting beaten about the head and shoulders, every time Reality rears it's ugly head. :o
Lord knows, the PLANS are no help! :'(
Especially, because I keep adding in Cool Things, that aren't IN the plans. 8)
Hence, the sometime re-adjustments to the build. :-X
20250522_164945 1024X768.jpg
Ah, well.
That tape-the-back trick is paying off well; I'll be doing that to the hand rail backing doublers, when I flip them over.
20250524_134338 1024X768.jpg
So how DO you move an unwieldy, floppy, boat deck all by your lonesome? ???
It's not a matter of weight, so much as bulkiness so first off, make it less floppy.
20250523_094825 1024X768.jpg
Then lift it up on one side and simply plop it down on the hull! :
A far cry from the partial build I dragged out of a Wisconsin barn, 18 months ago.
Charles Brennan
Looks amazing CB - and like a fun little boat!!