Woke up to the best weather we've had all month, in August.
Immediately put the first coat of epoxy on the poplar boards, that will bridge the bench seats.
20250826_102237 1024X768.jpg
Take a look at all the "flat" spots on the wood. I was surprised to see the Poplar soaked up epoxy, to an even greater degree than Okoume plywood does. :o
More "flat" spots on the Poplar.
20250826_102232 1024X768.jpg
Added graphite to the mast step block and the mast partner; since they are going to get a lot of wear and tear (stepped/un-stepped, etc.) and they'll need more abrasion resistance.
Everybody else just got a regular coat of epoxy.
The 2nd coat of epoxy looked a little more normal, in terms of coverage.
20250828_124448 1024X768.jpg
Everybody else looked about like you'd expect, in normal epoxy absorption.
20250826_151844 1024X768.jpg
Finally! :D The third coat was charm! 8)
20250826_154927 1024X768.jpg
Flip all these guys over and I'll be ready for the next three coats of epoxy.
20250826_154933 1024X768.jpg
Best of all: The weather was soooooo good, that I was able to get all three coats done in a single day! A New Record! ;D
While the epoxy was curing, I stayed busy sanding the fillet on the bulkhead #2 to deck joint and taking it from this:
Deck_Fillet.jpg
To this:
20250826_111711 1024X768.jpg
Flipped all the boards over and began the first of another three coats of epoxy.
20250827_113534 1024X768.jpg
Also flipped over the mast partner blocks and hit them with graphite-infused epoxy.
20250827_113547 1024X768.jpg
Had some black graphite epoxy left over and decided to touch up the oar holder cutouts, since that will be another wear-and-tear point, that would benefit from abrasion resistance.
20250827_113623 1024X768.jpg
A continuing argument in my sub-conscious was where to store the upper half of the oars.
Try as I might, I could not get both sets to fit behind the (future) coamings.
There simply wasn't enough room to lay them in there, side by side.
20250827_113633 1024X768.jpg
So I got on-line and queried other SCAMP owners as to what they had done.
Turns out, they cut TWO sets of holes so that the oars sit on TOP of one another, not side by side.
Since all the pics I had seen already had the coamings in place, I was unaware of the upper hole.
DOHHHH!!! :-[
Beginning to wonder if when I get this boat finished, I'm going to be too senile to know which way to point the tiller!! :P
20250830_112953 1024X768.jpg
Sure, it's an easy fix if you can only bring yourself to: THINK!! :P
20250830_113004 1024X768.jpg
Ah, well.
Fewer and fewer pieces all the time!! :) What happened to all those small blocks? ???
20250828_124456 1024X768.jpg
Glued to the underside of the cabin roof plywood.
Couldn't really clamp them like I would have liked and relied on diving weights, to hold them in place.
20250829_112823 1024X768.jpg
Slathered glue on the sides of the bulkhead cabin cleats and fastened the sides on.
Catch that gap on the lower left side of the cabin side panel.
20250829_112833 1024X768.jpg
While the epoxy glue is still a little "green" I'll remove the screws.
20250829_112846 1024X768.jpg
With the last of the glue, I was able to attach the bulkhead doubler, that also acts as an oar stop.
20250829_112854 1024X768.jpg
Since everything on a small boat has to do double duty.
Cleats re-visited, part 3:
My sub-conscious, which keeps track of EVERYTHING. wasn't happy with the cleat positioning >:( and so I compared it to pics of SCAMPS, on-line.
Did not agree with typical cleat placement, because I think they are mounted so high on Bulkhead #4, that coiling lines on the cleats would be problematic.
CabinCleats_1.jpg
This is an older SCAMP with the bulkhead cleat mounted pretty far over to the side, because the original design that had a wider bulkhead cut-out.
CabinCleat_2.jpg
But that gave me a good clue as to where I needed my cleats.
Straddling where the added bulkhead insert went so it's not too close to the sides and has room for coiled lines.
20250830_105248 1024X768.jpg
Just had to move the holes over to the side one "cleat width".
More holes to fill, but at least my subconscious will stop nagging me. >:( (Maybe.) ::)
Having rashly :-[ flush-trimmed the deck where it is supposed to support the cabin sides, I had to apply duct tape inside the cabin, to support the gap in the cabin side fillet.
20250830_112910 1024X768.jpg
This will keep all the filleting material from dripping down the the inside of the walls
20250830_113049 1024X768.jpg
Worked! :D
20250830_131034 1024X768.jpg
Look, Ma! No gaps!! ;D
20250830_131041 1024X768.jpg
They will also get a strip of fiberglass tape, to re-inforce the cabin sides, after the fillet cures.
Had just enough left-over fillet material to finish the fore-deck drainage doublers.
20250830_133903 1024X768.jpg
But not enough to finish filling the gaps around the fore-foot.
20250830_133908 1024X768.jpg
A job for the next left-over filleting material.
In a burst of enthusiasm, I was going to glue on the roof, but inclement weather dissuaded me.
I also realized that it will be FAR easier to do all 8 of the vertical cabin bulkhead fillets BEFORE the roof goes on. :P
Thinking about it some more, figured I was starting to get "Get 'er Done-itis" and needed to keep myself disciplined and on track.
It would be a shame to slop through it at this stage, when I have been fairly steady so far.
As I originally decided: It will take as long as it takes and that's all there is to it.
20 months and counting. :-X
Ah, well.
Charles Brennan
Man, that's a lot of epoxy work for one day! Glad for more cooperative weather.
20 months... that's how long it took me to build Disciple Ship. That included a 2 month hiatus. Because I finished at the holiday season, it was another 2 months before her maiden launch which happened to be on my birthday (that'll be one I'll never forget).
Yep, stay the course. Too much invested to not finish well.