After applying primer paint and some light sanding, I was ready to paint all the various pieces.
20251009_111004 1024X768.jpg
I got so much cross-contamination on the different paint colors between the port light frames and the grate (I really am a Painting Slob!) :P that I banished the port lights to the garage.
Which is why they are missing from subsequent pics. :-[
And skipping ahead to the third coat (on this side).
20251009_120607 1024X768.jpg
Epoxied these planks back in August and it was now time to wipe off all the dust . . . . . . . . .
20251009_111014 1024X768.jpg
. . . . . . . . . and give them a primer coat.
20251009_120613 1024X768.jpg
So I could start applying top coats.
20251010_115901 1024X768.jpg
Needed to build up the inside walls of the extended-height "SCAMP ramp" and was mildly impatient to get the pieces cut, fitted, epoxy triple-coated and then glued in place.
Seemed like a lot of delay for such a small task, :-X but it needed to be done before fiber-glassing the cabin roof.
Then I had a thought.
20251010_145819 1024X768.jpg
Hey! Remember THIS disaster, from last month?!? ???
No? ???
That's what you get, >:( for not reading all my posts!! ;D
There was just enough usable surface area to make ramp inserts and they were already epoxy coated!!
(And why you NEVER throw anything away on a Boat Project, until after the thing's in the water!) ;)
20250915_105105 1024X768.jpg
I only had to cut one edge so the exposed side, I arranged to be facing up and I could get the requisite 3 coats of epoxy on the exposed edges, when I fiber-glassed the cabin roof. 8)
Cleaned up, sanded, and ready for fiberglass! ;D
20251011_132505 1024X768.jpg
It was so windy, the day I was doing this, I had to clamp and tape the cloth, because it kept blowing off the roof.
20251011_104251 1024X768.jpg
A wall paper brush works wonders for smoothing out the fabric.
20251011_105128 1024X768.jpg
Even though it was 6oz. fiberglass, it was a very close weave and was a major PITA >:( to wet down, thoroughly.
20251011_115229 1024X768.jpg
I was reduced to lifting a corner at a time and wetting down any "dry spots" and laying the fabric back down, again.
Also had issues with stubborn trapped air bubbles, that had to be squeegeed down to the nearest edge.
As usual, Persistence Conquers All! ;D
After trimming the unused fiberglass, while still "green".
20251011_174640 1024X768.jpg
That tight fabric weave really paid off, when the 2nd coat of epoxy filled in the weave.
20251013_142236 1024X768.jpg
Actually had to lightly sand the top to apply the third coat of epoxy , because I worried about it bonding sufficiently, to such a slick surface. 8)
While I was top coating the port light frames, I took the opportunity to touch up some dings in the rudder stock and the rudder blade.
20251011_132431 1024X768.jpg
(I can tell, I'm going to have a really Bad Case of "Newitis", :o when I finally get this boat in the water).
Skipping ahead to the 3rd coat on the 2nd side.
20251014_104413 1024X768.jpg
A bit of a problem here, with a flat-bottomed Nav light block mounted on a curved surface; wanted a closer fit.
20251014_094637 1024X768.jpg
Solution? ???
20251014_094703 1024X768.jpg
Adhesive-backed sand paper, stuck on the roof! ;D
Rub the block back and forth, vigorously . . . . . .
20251014_094926 1024X768.jpg
. . . . . . . for a MUCH better fit! 8)
20251014_094837 1024X768.jpg
Having learned a bitter lesson recently, :'( I added some grease to the hole-alignment bolt; needed so that the block would not slide around on the roof, after gluing.
20251014_095114 1024X768.jpg
And so that the bolt would not become a permanent piece of the boat! :o
Added a lead dive weight until the glue started to squeeze out.
20251014_104436 1024X768.jpg
Also glued up the grab rail to the roof.
20251014_104440 1024X768.jpg
Not quite as flush as I had originally hoped for, but a belt sander should whip it into shape, pretty quickly.
20251014_104450 1024X768.jpg
I generally judge my progress by the number of pieces/parts I am juggling, at any one time.
The 7 pieces at middle and left on the next pic down, are going to eventually be a main-sheet swivel-block thwart.
(Had to check, that I said that right!) :P
Here's an example:
swivel_block.jpg
20251013_142249 1024X768.jpg
The two blocks on the right, are another example of the difference between Planning and Reality.
Planned and planned and planned, to make SURE I had backing blocks for all the deck and cabin roof hardware and TOTALLY FORGOT!! :-[ The anchor painter clam cleats.
Fortunately, where they go I can still reach under the now-completed deck, to glue them in place; all I had to do was bevel one side, to clear the hull-deck fillet.
On Urchin, I always had an anchor painter permanently lead from the bow to the cockpit and secured with a clam cleat, since I anchor exclusively from the cockpit.
(It's the cleat directly in front of the goal post, in the pic below.)
Anchor_painter_cleat 1024X768.jpg
To anchor, I remove the anchor and rode from the cockpit lazarette locker, tie the anchor painter to the end of the rode, snatch on a snatch block on a 20 foot line and toss the anchor overboard.
To retrieve the anchor, I pull on the line and use the block and line to bring the painter end back into the cockpit.
I needed two of them for the SCAMP, since I never know which side I am going to anchor from.
Needed to drill holes for the halyard cleat.
20251015_100636 1024X768.jpg
Also needed to know where the halyard turning block was going to be mounted.
Pressed a scrap piece of mast and the upper mast partner into service, to get an idea of where to drill.
20251015_100646 1024X768.jpg
After all the holes in the roof were drilled . . . . . . .
Let that sink in, for a minute. ???
ONLY Sailors, would DELIBERATELY drill holes in a roof! ::)
And then I OVER-drilled the holes, :P for filling in with thickened epoxy.
It's great to finally get out from under the tyranny of: wait until cured, or wait until dry, on these steps.
Now I can run concurrent tasks that are independent of cure/dry times. 8)
I can feel the Progress accelerating!! ;D
Charles Brennan
Great report! I feel the excitement/anticipation building.