SCAMP Sail on Lake Weir . . . .

[Charles Brennan]

My back-ordered Newport NV-300 series (NV-46) trolling motor finally showed up and I wasted no time in wiring it up. 
It came with a 50 Amp circuit breaker, on the theory that if you run aground with a gas motor, the prop just stalls the motor.
But an electric motor simply keeps increasing torque and current draw, until something burns up inside, so the breaker (hopefully!)    mitigates that.
Looks like this:
You cannot view this attachment.
And I had to immediately modify it for my application,    since I wouldn't be able to easily reset the breaker, where I would have to wire it.

You can see the reset button on the left side of the breaker at the center of the pic.
Now imagine trying to get to it, if it were on the right hand side. 
You cannot view this attachment.

Bright and early the next morning, left at the crack of 10 o'clock    and went over to Lake Weir, a coupla hours from my home, to learn more about the characteristics of the boat I had just built. 
I wanted to wring it out a little on a lake and Lake Weir was a good candidate, since it had a nice ramp and docks I could tie off to and no treacherous shoals and mud flats 50 feet from the ramp.
(Still mildly gun-shy, from the initial launch at Cedar Key's inside ramp.) 
I also elected not to put up the Bimini top, so I could see all the rigging and sail shape, more easily.
While probably required for cruising, it's largely superfluous for day sails, I think.
You cannot view this attachment.
Rigged and ready to launch!! 
(With the sail down, this time!) 

Launching was once again fairly uneventful.  Felt like I had the trailer dialed in pretty good, at this point. 
You cannot view this attachment.

With the exception of an off-shore wind from the lake, pushing the boat around onto the ramp.     
Had to move the truck out of the way to reach the lines and maneuver it over to the dock where I wanted it.
You cannot view this attachment.
Once I was ready to go, I flipped the switch on the trolling motor and backed slowly out, at speed setting 2 (of 3) in reverse and directly  into a wind, on my stern.
Had there been no wind, speed setting 1 probably would have been sufficient.

Once I was out in the lake proper, I figured I'd play around with the trolling motor speed settings and watch the Bluetooth Smartshunt readings on my phone.
You cannot view this attachment.

MAN!!    That NV-46 trolling motor sucks down some current! 
You cannot view this attachment.
Here is the current draw I measured, from the 1 to 5 setting on the throttle:
Setting 1: 11 Amps
Setting 2: 14 Amps
Setting 3: 20 Amps
Setting 4: 24 Amps
Setting 5: 40 Amps 
The rule of thumb used to be about 1lb of thrust for 1Amp of current draw, so 40 Amps of draw at 46 lbs of thrust, shows that they're making the motors a little more efficient, these days.
Speed ranged from 2½ knots, down to 1 knot, motoring directly into the prevailing 10- 12 knot winds
The time remaining increased with speed/current attenuation, but they generally showed about a 5 nautical mile range with the sweet spot in the mid-range settings, at the different speeds, which was what I had expected.

All that playing around, got me from a 99% charge when I started, down to 97-98%. 
I can live with that! 
I hadn't even bothered with setting up the solar array, so it's good to see that on most day-sails, I won't really even need it.
After I had some preliminary data recorded to help my energy calculations along, I next concentrated on actually, ya know, sailing the boat.
Initially, I was underwhelmed. 
Got .8 knots, maybe 1¼ knots and wondered if this Project had been a mistake. 
Got in irons once,  and then  looked up.
You cannot view this attachment.
Hmmm . . . . .  maybe two reefs is a little aggressive in 10 -12 knots . . . . .

Although I seemed to be steadily moving away from where I launched, despite what the abysmal numbers were showing me.
You cannot view this attachment.

Decided to shake out all the reefs and see what happens.
You cannot view this attachment.

The boat suddenly comes to life, that's what happens!! 
The tiller suddenly felt like I was holding a living thing! 
You cannot view this attachment.

That's a LOT of sail up there!! 
You cannot view this attachment.
Charles, why is there a nettle missing on the second row of nettles?!? 
Because SOMEBODY    used too small a line and the knots kept pulling through the grommets; going to have to move up to ¼-inch line.

And there's even more sail, up front!!
You cannot view this attachment.

A little heeling.
Ya know when you're driving the family sedan down the Interstate at a sedate 70 mph?? 
Then you get out and go in to the rental go-kart track and suddenly feel like you're ZOOMING (at all of 30mph) because your butt is so close to the ground?!? 
That felt like much the same difference to me, from the SCAMP's cockpit being closer to the water than when I was sailing in Urchin's cockpit.
I was doing 2½ - 3½ knots and felt like I was ZIPPING!! 
You cannot view this attachment.
After a while, I became aware of what seemed like a lot of slapping and wave action on the hull, which was odd,    on a comparatively calm day.
I eventually figured out that I had neglected to screw in the ballast tank plug, before I topped the tank off with the bilge pump.
DOHHH!!!! 
The tank had receded to its normal  ½ full level, level with the hull's waterline and was sloshing!!
Then looking up, I noticed that I had also forgotten to put the halyard end around the right-hand side of the mast!! (Which explained the tacking efficiency and getting caught in irons.)
DOHHH!!!! 
Wondered for a moment, whether it was Inexperience or Senility, behind all these issues!! 
No doubt about it: I need to make me up a detailed checklist and start using it, until this stuff becomes second nature.

The SCAMP foot well is one of the major ergonomic improvements to the SCAMP design and I finally had a chance to appreciate it in action.
You cannot view this attachment.

I sailed back and forth across the lake on various points of sail and discovered the SCAMP points easily as close to the wind, as the Windrose did.
(i.e. about as close as your average Spanish Galleon.) 
I decided to drop the sail while still well out in the lake and much further away from the docks, than where I usually drop sails.
It's actually much easier to do, rigged with lazy jacks.
You cannot view this attachment.

Motored in without issues and made a perfect docking, since nobody was around to see it. 
You cannot view this attachment.

Right here is where things went sideways and where the gods decided to remind me that as a Brennan, I'm eternally damn'ed. 
Retrieved the boat and pulled it out to the staging area and discovered that it was not centered on the trailer properly.  The skegs had completely missed the aft self-centering rollers.
Backed it in again, so I could re-float the hull and position it better.  The wind kept trying to push the hull sideways and I needed to use a dock line to hold it in alignment.
Since I had backed in quite a ways, I was concerned about the water level height and left my keys in the truck, so I wouldn't get the electronics on the key chain wet.
A wind gust closed the truck door.
And apparently from decades of electronic security and access control, I had reflexively locked the door, as I exited the truck.
Locked out of my truck with the engine running and with my phone also locked in the truck, so I couldn't even call for a locksmith.
DOHHH!!!! 

Finally flagged down a park ranger and borrowed her cell phone, to call for a locksmith.
While waiting, I basked in the compliments of passing boaters, launching and retrieving their boats from the lake.
Seems like EVERYBODY, loves a SCAMP. 
After I was back in my truck again, I decided to add another procedure to my checklist:
Windows down, when launching or retrieving. 
On the drive home, I came to the conclusion that the same depth of immersion that made for a successful retrieval at Cedar Key's inside (shallower!) ramp, put the trailer in too deep at Lake Weir.
As a result, the aft end of the hull floated too high above the end rollers and never took advantage of the self-centering rollers to center the skegs; gonna have to watch out for that. 
But for the first time really SAILING the boat, up until then, the sailing had been GREAT!! 
I decided overall, it was a good day with a slightly sour finish but also, one with much food for thought.

Charles Brennan

[Doug SC]

Your story about the keys and the wind at a deep ramp sound like you are talking about me...October 2018 Mark my nephew and Joe his friend on their first overnight kayaking trip, Mark's uncle locked his keys in the car. Joe found the end of an old car antenna which we bent to a shape that we could unlock the car by snaking it down inside the window. Just today as we took out at the ramp on Lake Monticello the wind picked up enough to cause the scamp to do what yours did. We also got it right on the second try. It just sounds like sailing to me. 

Bill and I sailed my Scamp yesterday and today on Lake Monticello staying overnight on one of the islands. We had good winds for sailing yesterday. Today was calm in the morning so we use the new electric motor. We both found it to be impressive using the voodoo method (no numbers)! The wind picked up enough to sail but you had to try to stay in it as it was spotty. That is until we got near the ramp to takeout when it freshened.
A few photos of camping at the island. I slept on the scamp and Bill in a tent.
You cannot view this attachment.

You cannot view this attachment.

You cannot view this attachment.

 

[Charles Brennan]

Doug, That last pic of your SCAMP was great!    Embodies the essence of what the SCAMP was designed for namely, exploring, gunk-holing in small coves, and camping out.
Nice tent.  Am I to infer that the previous Amazon one-man tent experiment didn't work out? 
I'm still going back and forth, on a pre-fab versus custom, tent arrangement and my time-frame is starting to get tight.   
(Visions of draping a tarp over the Bimini top, at the FL120!) 
Are there any water incursion issues on the tent edge, at the transom? 
About how long does it take to set up? 

Inquiring minds want to know!

Thanks,
Charles Brennan

[Chris Muthig]

Reminds me a little of that trip we did in my 17' hydrasport, off of Fort Lauderdale, broke down about 10 miles out in water far beyond anchoring capabilities.  Called Seatow, they let us know it would be around 3 hours to get to us, and it was approaching dark and there was no power / lights on board.  We rigged up the bimini like a spinnaker and used it to pull us in about half mile, but with the current we ended up off of Boynton Beach.  They picked us up and started towing us back, and the guy was inundated with calls so he suggested dropping us off in Boca at the Palmetto Park ramp, where I was to take a taxi (pre uber days) back to the boat ramp at Port Everglades to get my tow vehicle.  Get all the way down there and realize I'd left my keys in the boat 20-25 miles north.  Had to call my wife to bring me the spare keys at around 9pm, she was not happy about that!  I think we finally got home around 11pm.  Yet another powerboat breakdown!

[Doug SC]

Charles, I had both tents with me. It got down to 53F that night and the amazon one man tent would have been cold, so I used the one I made. I was warm enough inside from my body heat not to need more than a long sleeve shirt. That tent takes from 5-10 minutes, but I have not timed it. I put the aluminum sectional tent pole into the oarlocks Which is quick. I slide the boltrope at the front of the canvas tent through the track installed on the cabin top. I then attach the tab/toggle grommets (not sure what the name is) along one side to the pole. Then do the same along the other side. I then put the rest of the tent over the pole. I unzip the zipper that runs from the top just shy of the pole to the end near the transom. Once unzipped I put it over my head and standing through the zipper opening finish attaching the tab/toggle grommets down the sides and across the transom. water shouldn't get in at the transom as there is the raised edge already in place for that propose. The t/t toggles are on the water side of that. Now maybe along the side of the boat just in front of  the transom the short open area might let water in. However, the canvas is on top and should deflect it down past there. The 10 oz duck canvas with a water repellent treatment is amazingly waterproof. Even my untreated canvas tarp from Harbor Freight doesn't leak. My portholes allow me to remover their clear cover for ventilation as does the tiller opening (I added no-se-em mesh screen to them and to the tiller opening).

The amazon tent would require the fill-in boards to be placed between the seats but goes up quickly. A learned process you have to figure out when you first set it up and take it down. After that I like to tie the tent to the boat from all 4 corners of the tent. I haven't slept out in it. My one concern is in high winds and heavy rain as I haven't used this type of tent. Most of my tenting has been with more costly backpacking tents. What I really like about it is the ease of putting up and taking down once you understand how to fold it up and the amount of no-see-um mesh screen for good ventilation in hot weather. It might just fit under your Bimini. Which would give extra rain protection. Hot FL and a time constraint would suggest this tent would be a good start. I think it cost $70.

Both tents are bug proof!

I can post some photos later if you like.

[Doug SC]

Here is a link to a tent like I have. Its dimensions are 92.5"L x 39"W x 35.5"H.

https://www.amazon.com/Night-Cat-Pop-up-Camping-Tent/dp/B0CT8H39HS/ref=sr_1_3?crid=H6VNLMJHIXAR&dib=eyJ2IjoiMSJ9.DGL7vW1oI364Z5uC91eYjuelMNN7QrV2cky2P3uqvFHrs4Za1tgDW0tS1gtR2FoakT7IkfG1ulMmZX6t0dVLLrJCFObSe1kX4-b7FkK3DdlbOJLfK_47pND_JMJlNbVgAS41RH_6HLG9m8xdA2iAB_aedjKk9gD4XSE-pI2NxN3TTmaqYdRLoV8l30qlHiLrAmzc6J2rSXKJmnl8g0Tv001PjV67cbDWscfAncv4jWE.-eKTZYEwNe3XjM6_5cx58-2DEXSB20_DXyajgA9iP3k&dib_tag=se&keywords=one%2Bman%2Bpop%2Bup%2Btent&qid=1777053285&sprefix=one%2Bman%2Bpop%2Bup%2B%2Caps%2C186&sr=8-3&th=1

There are others that could work like this one which is 92.5"L x 39"W x 35.5"H.
You would have to attach the poles to the tent and the rainfly too. It would be a more involved set up. A rainfly would provide better rain protection in my opinion, but Captain Kidd set his out in a hard rain and it stayed dry. I have been wrong before.
 
Both tents are 92.5"L x 39"W x 35.5"H. I like the one I have. The rounded end hangs over slightly into the veranda but isn't a problem. It might be harder to fit the one with poles as it is rectangular in shape. I just don't know. I look forward to using mind when the nights are warmer.

[Doug SC]

Charles, after looking at these photos I don't think the tent with poles and rainfly would fit.

Here is the amazon tent I have on the scamp.
You cannot view this attachment.

Here you can see why it can fit with the very end unsupported under the roof.
You cannot view this attachment.

I have to let my tiller extend into the tent which might allow a bit of water dripping in during a rain, but it should be minor (I hope).
You cannot view this attachment.

It has a good amount of screen on all 4 sides for ventilation.
You cannot view this attachment. and I will have an added fan.

The folded-up tent out of the bag on the scamp.


You can push on the tent to have room to stand outside of it.
You cannot view this attachment.

It is roomier than the canvas one I custom made because it has 2 poles. If I made another canvas tent for it, I think I might also add another pole.

Here is the piece of canvas draped over the boat and the pole that is set into the oarlocks.
You cannot view this attachment.

I had to add a piece at the transom otherwise the rest of it is all one piece with only the zipper sewn into it and the piece at the transom.
You cannot view this attachment.

You cannot view this attachment.

A view of some of the tab/toggle gromet male ends on the transom.
You cannot view this attachment.

You can buy a 10-foot-wide piece as long as you would need and it would cover the whole cockpit with only the zipper/zippers, bolt rope and gromets being sewn in or added and no other seams needed.
 

[Captain Kidd]

Charles, so excited for your sail! Sorry for the miscues.

I'm using a similar tent to Doug's. It is so quick and easy to set up. Have not had it in rain yet. I've slept with it completely closed up and it does sweat unlike a tent with screen and rainfly.

[Travis Chapman]

I feel like everyone has that one event that changes the checklist forever... I also have the window-down policy so much empathy here. I'm also now wondering where my Newport curves went to; I have that same model on Panda Paws for trolling and was quite pleased, though not as smooth throttling as my old 24V Motor Guide. Pics look great as always!!

[Riley Smith]

CB that window down rule needs to be priority one 

PS. My truck has a positive traction switch I have only used a couple of time but Sunday was once I did. That ramp was SLICK and the tide was very low forcing me to back WAY down. All was well though and nary tire spin.

[Noemi - Ensenada 20]

After I locked my keys inside my running car, in a snowstorm, just before leaving for work....my policy has been to keep a spare set of keys IN my pocket at all times.  This has saved me from more embarrassment many many times.