It's "Curtains" for Urchin!! . . . .

Started by Charles Brennan, May 03, 2023, 09:37 PM

Previous topic - Next topic

Charles Brennan

Feverishly getting ready for the Cedar Key Small Boat Meet, this coming weekend.
This might be the least unprepared, I've ever been Not Ready! ;D 
There is so much stuff I have fixed and in good shape, I'm starting to worry/wait for the other shoe to drop.
I might even have a full set of curtains!

Located the fabric I bought about 18 months ago for replacement curtains and started hacking on it.
I'm absolutely hopeless with fabric shears, or any kind of scissors.
In 3rd Grade, when everybody folded up a paper lace doily, made a few strategic cuts and then ended up with a beautiful lace snowflake, I always ended up with three triangles.
Could never figure out how that happened.
But I'm a Holy Terror, with a snap blade and an L-square!  ;D
You cannot view this attachment.

Having decent tools (like a Sailrite LS-1) helps a WHOLE lot.
Even my wife (my biggest critic), was impressed with the stitches.
You cannot view this attachment.
The laptop at left, is because I can never remember how to wind bobbins, or thread the thing properly, without a YouTube video to turn me back into an Instant Expert.  ;)

Port Before:
You cannot view this attachment.
Port After:
You cannot view this attachment.
(Check those stitches at upper left.)

Starboard:
You cannot view this attachment.

And a view from outside:
You cannot view this attachment. 

I've got two days to do the forward ports curtains which are more difficult, being trapezoids and all, plus I want to make up a new companionway fabric cover, to improve night time ventilation while over-nighting.
If I don't get the fabric cover done in time for the Cedar Key Small Boat Meet, I still have some time to sew that up plus, maybe some new curtains for Porta-Potti Privacy in the forward cabin, before the FL 120.
That way, all the fabric in the cabin will match, like the CDO (It's like OCD, only alphabetized, like it SHOULD be!) personality, that I truly am.

So many of my tales/posts are of varying degrees of disaster, I felt a need to celebrate the small Victories, that occur from time to time, however infrequently.

Charles Brennan

Captain Kidd

Busy but interesting pattern. Nice job.

Zig Zag

   
Enjoy your Cedar Key weekend and see ya at the 120.
       
"Go ahead --- Leave me on the dock --- See if I care"

Travis Chapman

Charles, I had a hard time telling this: did you countersink the screws holding the knobs in place? Overall it's a great idea! Better than getting track lined up and fixed in place.
=============
SV Panda Paws
Windrose 18
Glyndon, MD

Charles Brennan

Travis, Thanks for your kind words.  The idea was stolen wholesale from a Captain Pauley DIY article in Small Craft Advisor.
I would refer you to the first half of a previous post where I described the installation in more detail:
https://trailersailor.com/forum/index.php?topic=121.0
You can see pics that show all the hardware used.
(Reproduced here, for clarity.)
You cannot view this attachment.

These were off the shelf (OK, off the internet) wooden drawer pulls from China.  They had threaded inserts, but they were metric and I didn't want to fool with non-standard hardware sizes, so I drilled out the inserts slightly to accommodate 6-32 machine screws.   
I'm not completely sure about your question regarding countersinking the screws.
On the hull side (6th or last pic down, this post) those are ordinary oval head Phillips 6-32 machine screws that were placed into a stainless steel finishing washer.
On the cabin side (inside, 3rd pic down, this post) those are truss-head 6-32 barrel bolts (in the plastic bag in the pic above) and although they might appear to be countersunk in the photos, they are merely very low profile and closely match the overall curvature of the knobs, but they DO stick out just a little.

Hope this clarifies,
Charles Brennan

Zig Zag

reminder --> Charles know you're watching tides --- almost 2 ft between hi/lo.  Enjoy your weekend.
 
"Go ahead --- Leave me on the dock --- See if I care"

Norm L.

Charles, have a great time. I'll wave as we go by Monday although there will only be the die-hards left.
We will be on our way to Palm Harbor to visit a friend for a few days.

Noemi - Ensenada 20

Charles, nice sewing!

You know how you understand how to wire things up, just because you KNOW from all those years of doing it?  Threading sewing machines is like that for me.  They're all about the same.

Tom G P 21

If you wanted to get real fancy, you could've made them double sided so they look as nice inside as outside. Maybe the "next" time you make curtains.   ;)

Tom G

Charles Brennan

Tom, I looked into double-siding the fabric for the curtains. (It was on sale and we bought plenty of fabric.)  But when I mocked it up, they acted almost like blackout curtains and I wanted the same general amount of light inside, as the old curtains admitted into the cabin. The old curtains were over 35 years old, possibly pushing 40 years, so the next time I need to make curtains, I'll be too old, or senile to know how to do it!! ;D

Hope this clarifies,
Charles Brennan